Amercoat Chemical Resistant Lining. Product Data/. Application Instructions. • High Solids, high performance epoxy novolac also defined. Amercoat – Download as PDF File .pdf), Text File .txt) or read online. This Safety Data Sheet is prepared in accordance with Annex II to Regulation ( EC) No. / AMERCOAT CHEMICAL LINING CURE.
|Published (Last):||12 August 2014|
|PDF File Size:||19.42 Mb|
|ePub File Size:||19.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
The product cures to a highly cross-linked coating with excellent chemical, solvent and water immersion resistance. If thinning is desired, use Amercoat 65 xylene. Apply Dimetcote 9H as soon as possible to prevent the blasted surface from rusting.
Amercoat flow control additive may be used to enhance flow and leveling of brush strokes and roller stipple.
Performance Industrial, Marine and Commercial Coating Systems
Minor Cracks in Horizontal Surfaces Cracks, chips and broken or flaking areas in concrete are not only unsightly, they can lead to further deterioration of the surface. This tool should be used as a guide only. Adding too much accelerator may will adversely affect the recoatability, appearance, and performance of the products.
When using Amercoat liquid to prime, apply the cement within the same day aamercoat after the liquid is dry to touch. Zmercoat surface profiles up to 3. Strain through a mesh screen.
Amercoat 253 pdf
A spare material line is recommended so one line can be thoroughly cleaned while the other is in use. For small or repair areas, use a hand held hopper gun such as a Quikspray Model 60AT. For immersion service and for optimum performance, surface akercoat must be at least 5 F above the dew point temperature. It is an air dry, ambient temperature cure primer and does not require a heat cure is a high solid system having a VOC content of 3.
Stir thoroughly until homogenous. Amefcoat those situations, a further degree of cleaning may be required.
Some batch-to-batch variation in color is to be expected. Caring for Irish Blue Limestone Products.
Do not apply at substrate temperatures below F [66 C] or above F [ C]. Multiple coats may be required to achieve proper film build and hiding with roller application. This application is simlar to mist coating.
Commercial Fishing Supplies | Seattle Marine & Fishing Supply Co.
Surface temperatures must be measured at various elevations from top to amerxoat and in each cardinal direction. Application by airless spray will require a mastic gun with a inch spray tip.
Higher surface profiles up to 5 mils are acceptable, but the product must be applied in a thickness great enough to achieve a minimum of 2. Do amercost thin VHA with any other solvent. Do not apply to steel temperatures below 50 F 10 C. Mechanical surface preparation should expose sub-surface voids and provide a surface profile equivalent to 60 grit sandpaper or coarser.
Discard wiping rags in closed containers. Below amrecoat F longer contact time may be needed and below 60 F, many graffiti materials may be difficult to remove.
For optimum service life, the surface must be completely free of all contaminants More information. Anti-corrosive system should have a minimum dry film thickness of 10 mils. To make this website work, we amerdoat user data and share it with processors. This is not to be confused with burned areas and does not require special treatment.
If more than two applications of Amerase are needed to remove stubborn stains, rinse the area with clean water and wipe dry before each additional application.
Protect surfaces from contamination prior to re-coating. Add powder component slowly under agitation until fully mixed. Ammercoat products work well over a variety of substrates, both for interior and exterior settings.
Precision Coatings manufactures high performance finishes based on innovative polyurethane and polysiloxane technologies. Hi-Temp VS does not soften in thermal cyclic service. Use a high quality natural bristle brush.
Follow with a clean water rinse. After the film is dry-to-touch, a fine mist may be applied over the coating to expedite curing in low humidity environments. Refer to Information Bulletin for detailed information on ventilation requirements for tank lining applications.