Revision date Amercoat S. Gloss aliphatic polyurethane topcoat. ( Series). Product Data/. Application Instructions. • High gloss topcoat. AMERCOAT 71 TC. MANUFACTURED BY. PPG. Search by product ID/Name. Search. Product Ranges. Car Body Paints · PPG Paints · Paint preparation and. This Safety Data Sheet is prepared in accordance with Annex II to Regulation ( EC) No. / AMERCOAT S CURE. MSDS EU
|Published (Last):||3 July 2018|
|PDF File Size:||13.15 Mb|
|ePub File Size:||7.29 Mb|
|Price:||Free* [*Free Regsitration Required]|
Polyamide Cured Epoxy Topcoat. High build epoxy intermediate coat or topcoat. Economical long term protection in Amercoat S is used as a finish coat in protective Typical systems using Amercoat S.
Excellent color and gloss retention. Amercoat S is normally applied over Amercoat epoxy primers or Dimetcote 9 Series, This product is photochemically reactive as defined by the South Coast Air. This mixed product is amefcoat reactive as defined by the South Coast Amercoat – Amro Agency Amerccoat B-1 and Amercoat G-1 are designed to indicate potentially dangerous “hot spots” on the exterior of reactors and pressure vessels resulting from If required Amerlock C can be overcoated with a wide range of Instruction and Material Safety Data Sheet must be observed during all Technical Service for guidance on chemical resistance.
Amercoat 78HB a durable, high performance, economical coating suitable for Flash Point Closed Cup. Examples of past fields of ameecoat can be found on Room and board housing and meals.
Sample questions are provided on the supplemental form to assist you. Amercoat S is an aliphatic polyurethane high-gloss finish coat used with a Refer to Amercoat S product data sheet for properties and use. To obtain the maximum performance for which Amercoat S is formulated, strict adherence to all application instructions, precautions, conditions and limitations is necessary. If conditions exist that are not within the requirements or limitations described, consult your Ameron representative.
Amercoat 450S Application Instructions – About OASIS AMERCOAT
Be sure primer is clean and amdrcoat when Amercoat S is applied. Application Equipment The following equipment is listed as a guide and suitable equipment from other manufacturers may be used.
Adjustments of pressure and change of tip size may be needed to obtain the proper spray characteristics. Separate air and fluid pressure regulators, mechanical pot agitator and a moisture and oil trap in the main air supply line are recommended. Environmental Conditions during application Air temperature: Ensure surface is clean prior to application. Application Procedure Amercoat S is packaged in the proper mixing proportions of resin and cure which must be mixed together before use.
Flush equipment with recommended cleaner before use. Stir both ameecoat and cure to a uniform consistency with a power ameecoat. Add cure to resin, and continue stirring for 5 minutes. For brushing and rolling, normally no thinning is required.
Apply a wet coat in even, parallel passes. Double coat all welds, rough spots, sharp edges and corners, rivets, bolts, etc. Check thickness of dry coating with a non-destructive dry film thickness gauge, such as Mikrotest or Elcometer. If less than specified thickness, apply additional material as needed.
Small damaged or bare areas and random pinholes or holidays can be touched up by brush. Repair larger areas by spray.
PPG Amercoat – Amro Agency SRL
In confined areas ventilate with clean air during application and drying until all solvents are removed. Temperature and humidity of ventilating air must be such that moisture condensation will not form on surface. Clean all equipment with recommended cleaner immediately after use or at least at the end of each working day or shift. When left in spray equipment, Amercoat S will cure and cause clogging.
Caution This product is flammable. Keep away from heat and open flame. Use with adequate ventilation. Avoid prolonged and repeated contact with skin.
Amercoat – Intercolor
If used in confined areas, observe the following precautions to prevent hazards of fire or explosion or damage to health: Do not empty into drains.
Take precautionary measures against static discharges. For specific information on hazardous ingredients, required ventilation, possible consequences of contact, exposure and safety measures see Safety Data Sheet. Safety Since improper use amercoxt handling can be hazardous to health and cause fire or explosion, safety precautions included with application instructions must be observed during all storage, handling, use and drying periods. Warranty Ameron warrants its products to be free from defects in material and workmanship.
Ameron makes no other warranties concerning the product. No other warranties, whether amerocat, implied, or statutory, such as warranties of merchantability or fitness for 45s0 particular purpose, shall apply. In no event shall Ameron be liable for consequential or incidental damages. Variation in environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results.
Amercoat S Amercoat – Amro Agency. Amercoat – Amro Agency. Amerlock C Amercoat – Amro Agency.