AMMCO 7000 PDF

View and Download AMMCO installation instructions manual online. Disc Rotor Lathe. Lathe pdf manual download. iv • AMMCO Brake Lathes. Safety. Safety Notices and. Decals. For your safety, and the safety of others, read and understand all of the safety notices and . Get AMMCO Disc Rotor Lathe Manual. Get all AMMCO manuals!.

Author: Tara Vulmaran
Country: Panama
Language: English (Spanish)
Genre: Literature
Published (Last): 12 May 2012
Pages: 495
PDF File Size: 16.96 Mb
ePub File Size: 2.66 Mb
ISBN: 386-4-52215-776-9
Downloads: 35284
Price: Free* [*Free Regsitration Required]
Uploader: Shakazahn

Don’t have an account? Retighten the arbor nut. Don’t show me this message again. Page 16 Brake Lathes Machining 8. Repeat the procedure for the other tool-bit holder. The cross feed speed control adjusts the feed rate from.

Turn each tool bit control the outer knurled knobs clockwise until the tool bits just contact the rotor faces. Your manual failed to upload Page of 20 Go. After the brake rotor is mounted on the arbor, install the silencer band.

AMMCO 7000 Installation Instructions Manual

Oiling The lathe is shipped from the factory with the correct amount and type of oil. Keep bystanders out of work area. Move the belt to the ammck groove that will give the correct spindle speed for the cut to be taken, Fig. Table Of Contents Cleaning Page 15 Brake Lathes The scratch will usually appear as an incomplete circle. Unplug unit from power source before servicing or adjusting. The cross also be operated manually using the cross feed handwheel. Even the smallest nick, scratch, or loose chip can cause incorrect rotor alignment, resulting in inaccurate machining.

  EDAIN MCCOY PDF

Don’t see a manual you are looking for? Now engage the automatic cross feed by moving the knobFig. Safety glasses, goggles, or a face shield contact persons in the akmco causing personal injury. B 10, and adjust the twin cutter so that the rotor is centered between the tool bits.

AMMCO INSTALLATION INSTRUCTIONS MANUAL Pdf Download.

Remove all adapters from the arbor after machining a rotor and wipe them clean – especially the inboard adapter. Or point us to the URL where the manual is located. Keep all guards, shields, and covers in place wmmco in working order. Page 19 Brake Lathes Care of Arbors and Adapters CAUTION Although the adapters, arbors, and the spindle are made of top grade steel and are turned, hardened, and precision ground to close tolerances, great care should be taken in their use, handling, and storage.

Identify the hazard levels used in this manual with the following definitions and signal words: Important Safety Instructions Safety glasses, goggles, or a face shield contact persons in the area causing personal injury. Move the tool bits inward until they just contact the faces of the rotor.

Also review the following general safety instructions. Safety Safety Notices and Decals For your safety, and the safety of others, read and understand all of the safety notices and decals included here and on the unit.

The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice. The self-aligning spacer should always be used adjacent to the arbor nut. Handle the adapters and arbors with care and store them on individual hooks. Brake Lathes Arbor Installation The 1″ arbor shipped with the lathe has been carefully matched to the lathe during final assembly and testing.

  FX2N-32ER-ES UL PDF

Page 15 Examine each adapter and the arbor for nicks, burrs, chips, dirt, and rust. Installation Replace or repair damaged or worn cords immediately soon as it is received. Reset the collars if necessary.

Refill as necessary with EP gear oil and check the oil level often. Generally, finish cuts should be. Comments to this Manuals Your Name. Also inspect the rotor hub for loose or damaged bearing cups. Witness marks have been etched onto the arbor and spindle for repeatable, precise alignment.

The signed bill of lading is AMMCO electrical and electronic based machines are acknowledgement by the carrier of receipt in good con- designed for nominal line voltages with variations of dition of shipment covered by our invoice.

Brake Lathes The scratch will usually appear as an incomplete circle. Reconditioning Disc Brake Rotors-set-up Fig. Got it, continue to print. Turn the cross feed handwheel clockwise until the tool bits are near 70000 rotor hub, Fig.

Spindle Speed – Release the belt tension by moving the V-belt adjusting lever clockwise, Fig.