AS NZS 1554.1 PDF

AS/NZS Australian/New Zealand Standard. ™. Structural steel welding. Part 1: Welding of steel structures. A. S. /N. ZS AS/NZS Australian/New Zealand Standard™. Structural steel welding. Part 1: Welding of steel structures. Originated in Australia as AS CA8— Join our Senior Welding Engineer Alan McClintock as he brings to attention what to do if using steels not manufactured to AS/NZS

Author: Arashisho Matilar
Country: Syria
Language: English (Spanish)
Genre: History
Published (Last): 11 January 2010
Pages: 77
PDF File Size: 18.53 Mb
ePub File Size: 5.83 Mb
ISBN: 236-3-99385-963-8
Downloads: 11638
Price: Free* [*Free Regsitration Required]
Uploader: Yozshurisar

No change is required.

For the purposes of Table 6. Flux fused in the welding process shall not be re-used. This Standard does not apply to underwater welding. Welding and cutting under jzs see Clause 5.

AS & AS/NZS – Australian Welding Institute

COPYRIGHT rd Unacceptable undercutting shall be made good by either the deposition of additional weld metal in accordance with this Standard or the removal of the undercut by grinding in accordance with Clause 5.

Due to changes in the welding consumable classifications systems used in Australia and New Zealand, reference should be made to Appendix F for guidance on the extension of weld procedure qualification. Where either of the two additional spots fail, the entire weld should be examined, and repaired as appropriate.

Nze are two t Transverse guided bend test Method 5.

Equal width rectangular hollow sections Where the end of a rectangular hollow section member is welded to the surface of another rectangular hollow section member of equal width, the welding procedure shall be qualified in accordance with Clause 4. Guidance as to the extent of non-destructive examination is given in Table 7. All welding and fabrication work must be performed using qualified procedures.

  CONSTANTINE A BALANIS MODERN ANTENNA HANDBOOK PDF

Welder qualifications for welding to a specified welding procedure shall remain valid, provided the following criteria have been met: Co py rig This Standard was issued in draft form for comment as DR See Appendix D, 1554.1 k.

Thank you for interesting in our services. Flux-cored arc welding FCAW. Correction of distortion see Clause 5. They reflect the latest scientific and industry experience. A welding procedure specification shall be developed from the PQR, based on the limits of the essential variables of Clause 4.

For workmanship tolerances of weld preparations, see Table 5. Consumables 5154.1 gas-tungsten arc welding conform to Column 7 of Table 4. Ze a For material with a thickness of less than 36 mm, Item o of Table 4.

All t Submerged arc 12 max. Test reports that may be used for revalidation or prolongation of welder qualification should include WPS number, date welded and welder identification.

Steel Construction Historical structural steelwork. Steel type see Table 4. Visit our web sites www. See Appendix D, Item v. Thus, such instructions should be agreed between the fabricator and principal.

AS 1554.1 & AS/NZS 1554.1

Where welding consumables meet the above requirements and comply with one of the following relevant requirements, they shall be deemed prequalified and require no qualification testing: No peening shall be done on the root or surface layer of the weld or in the base metal at the edges of the weld. We need your help! Demonstrating compliance of imported material with th V 25 6 max. Co py rig ht The Charpy-V test temperature shall be the lower of the relevant temperature given in Table 4.

  BERTIN SEMIOLOGY OF GRAPHICS PDF

The effective area of a slot weld shall be as for a fillet weld of the same size and effective length.

Test reports for non-destructive examination shall comply with the appropriate Australian Standard and shall include the following additional information: Welding of steel structures subject to high levels of fatigue loading In welds made using self-shielded flux cored consumables in combination with other consumable types see Clause 4.

Low and intermediate alloy steel electrodes for manual metal-arc welding of carbon steels and low and intermediate alloy steels superseded The connections shown in Figure 4. This standard underwent a major revision and was published on 23rd December Welding positions shall comply with AS see also Table 4.

Statements expressed in mandatory terms in notes to tables and figures are deemed to be requirements of this Standard.