ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Gardajora Taumuro
Country: Panama
Language: English (Spanish)
Genre: Life
Published (Last): 23 July 2007
Pages: 91
PDF File Size: 19.15 Mb
ePub File Size: 9.32 Mb
ISBN: 458-1-96676-786-5
Downloads: 43796
Price: Free* [*Free Regsitration Required]
Uploader: Tygoshicage

Notwithstanding the absence of a signature, the organization submitting the document is responsible for the content of the document.

However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. When required, minimum coil weights s682 subject to negotiation. Link to Active This link will always route to the current Active version of the standard. Aastm agreed by purchaser and supplier, other silicon ranges are permissible. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

ASTM A, AM_百度文库

Normal coiling or piling does not provide a 3 Where an ellipsis. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? This edge is produced when the width tolerance and edge condition are not as exacting as for No.

The elements comprising the desired chemical composition are speci? Number of Tests and Retests Last previous edition A — Within the text, the SI units are shown in brackets. When the amount asm vanadium, columbium, or titanium is less than 0. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

  LIBRO CON QUIEN ME CASARE PDF

This is produced when the edge condition is not a critical requirement for the?

ASTM A682 Grade 1074

B The sum of copper, nickel, chromium, and molybdenum shall not exceed 0. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge. Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi? However, the document shall clearly identify the organization submitting the document.

Revision to Table 2.

Over 12 Width Tolerance, Plus and Minus, in. Thickness Tolerances Plus or Minus, in.

Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis. Originally published as A — Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size. The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis.

NOTE 2—Camber tolerances as shown in the table are for any mm length. However, under SI the preferred term in mass. A superscript epsilon e indicates an editorial change since aastm last revision or reapproval.

  EXTRON MPX 866A PDF

However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Rejection and Rehearing C When the chromium is speci?

Combining values from the two systems will result in nonconformance with the specification. Limits on such elements are by agreement between purchaser and supplier.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Individual reprints single or multiple 6a82 of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Combining values from the two systems will result in nonconformance with the speci?

When the amount of copper, nickel, chromium, or molybdenum is less than 0. Stay on Page Continue to Compass. Over 12 Through 11?

Dimensions, Mass, and Permissible Variations 9. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values.