ASTM B117-07A PDF

The salt spray (or salt fog) test is a standardized and popular corrosion test method, used to ASTM B was the first internationally recognized salt spray standard, originally published in Other important relevant standards are. Designation: B – 07a Standard Practice for Operating Salt Spray (Fog) Apparatus1 This standard is issued under the?xed designation B. ASTM B Testing, also known as a Standard Practice for Operating Salt ASTM B Testing requires controls over many operational parameters such as: .

Author: Narg Dourn
Country: Algeria
Language: English (Spanish)
Genre: Automotive
Published (Last): 10 August 2012
Pages: 222
PDF File Size: 20.2 Mb
ePub File Size: 17.39 Mb
ISBN: 717-5-33924-408-4
Downloads: 21079
Price: Free* [*Free Regsitration Required]
Uploader: Grolabar

Careful attention should be given to the chemical content of the salt. This qstm has been approved for b11-07a by agencies of the Department of Defense.

Specimens shall preferably be supported from the bottom or the side. Heating Blocks for Evaporators. Test specimens are placed in an enclosed chamber, and exposed to 1 of 2 possible changing climate cycles. Nozzles may be located at the ceiling, or 0.

ASTM G85 is an example of a test standard which contains several modified salt spray tests which are variations to the basic salt spray test.

Hot-dip galvanizing produces zinc carbonates when exposed to a natural environment, thus protecting the coating metal and reducing the corrosion rate. NOTE 10—A solution having a speci?

From Wikipedia, the free encyclopedia.

NOTE 7—If the tower is run outside of these suggested temperature and pressure ranges to acheive proper collection rates as atsm in Options for corrosion chambers. This is followed by 0. This spray is set to fall-out on asm the specimens at a rate of 1. Usually, the materials to be tested are metallic although stone, ceramics, and polymers may also be tested and finished with a surface coating which is intended to provide a degree of corrosion protection to the underlying metal.

Most commonly, the time taken for oxides to appear on the samples under test is compared to expectations, to determine whether the test is passed or failed. Retrieved from ” https: In either case, the exposure to salt spray may be salt water spray or synthetic sea water prepared in accordance with the requirements of the test standard. A typical arrangement is shown asttm Fig.

  LA CAZA DEL SNARK LEWIS CARROLL PDF

SAL 3000-FL

An 11 to 19 L 3 to 5-gal reservoir is required within the chamber, with the level controlled. Once a year the corrosivity of the salt spray test chamber has to be checked. Painted surfaces with an underlying hot-dip galvanized coating can be tested according to this method.

The first climate cycle comprises a continuous indirect spray of neutral pH 6. A common method of introducing the air is through an air dispersion device X1. Most Salt Spray Chambers today are being used NOT to predict the corrosion resistance of a coating, but to maintain coating processes such as pre-treatment and painting, electroplating, galvanizing, and the like, on a comparative basis. Preparation of Test Specimens 6.

All necessary material for determining corrosiovity test panels, chemicals and other accessories you can buy in our webshop. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

salt spray test, ASTM B, corrosion tests

The pH measurement shall be made as described in 8. This is followed by 1. The longer the accelerated corrosion test, the longer the process remains out of control, and larger is the loss in the form of non-conforming batches. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. This test can be used to test the relative resistance to corrosion of coated or uncoated aluminium alloys and other metals, when exposed to a changing climate of acidified synthetic seawater spray, followed by a high humidity, both at an elevated temperature.

  INTRODUCTION TO PSYCHOLOGY PLOTNIK 8TH EDITION PDF

Position of Specimens During Exposure 7. For this reason the salt spray test is most often deployed in a quality audit role, where, for example, it can be used to check the effectiveness of a production process, such as the surface coating of a metallic part.

Suitable apparatus which may be used is described in Appendix X1. Last previous edition approved in as Sstm — Please log in, in order to get access to prices, ordering and inquiry functions.

If these conditions are met, you can assume that your machine runs fine. By using this site, you agree to the Terms of Use and Privacy Policy.

Salt spray testing is an b117-07x corrosion test that produces a corrosive attack to coated samples in order to evaluate mostly comparatively the suitability of the coating for use as a protective finish. Copper content shall be less than 0. The chamber has the following features: Variations to the salt spray test solutions depend upon the materials to be tested. When the pH of the salt solution is adjusted at room temperature, it is therefore necessary to n117-07a it wstm 6.

The procedure in Appendix X3 for measuring the corrosivity of neutral salt spray cabinets with steel panels has no bias because the value of corrosivity of the salt spray is de? This produces a corrosive environment of dense salt water fog also referred to as a mist or spray in the chamber, so that test samples exposed to this environment are subjected to severely corrosive conditions.

Suspension from glass hooks or waxed string b117-07 be used as long as the speci? The pH of the collected solution shall be 6. Test solution tank L.

Posted in Sex