ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Taujora Brak
Country: Jamaica
Language: English (Spanish)
Genre: Finance
Published (Last): 1 March 2007
Pages: 388
PDF File Size: 16.63 Mb
ePub File Size: 14.44 Mb
ISBN: 342-8-98902-450-1
Downloads: 20582
Price: Free* [*Free Regsitration Required]
Uploader: Dojin

The panel is mounted horizontally, tape side up, asmt the d364 end of the tape allowed to hang vertically over the rounded end. Between uses, the panels test surface shall be protected from scratches and contamination, and the panels stored at conditions described in 8. These censored data may have a time to termination rather than a time to failure.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Originally approved in The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other.

ASTM D3654/D3654M – 06(2011)

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability d36554 regulatory limitations prior to use. In order to offer you the best service, Algomtl uses cookies. Where width or other factors causing high adherence to backing make it impossible to remove the specimen at the prescribed rate, remove it at a rate as close to mm [30 in.


A standard mass d3645 attached to the free end of the tape and allowed to act for the speci? Measure any slippage that has occurred to the nearest 1 mm [1?

The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches from one mill, and within batches. The test plate with adhesive specimen is vertically hanged on the stand asm its bottom is attached with a r3654 weight. Procedure H may be used to compare the shear adhesion of tape applied to a standard steel surface and tested at an elevated temperature. Procedure D measures the shear adhesion of a pressure-sensitive tape to a nonstandard fiberboard, liner board, corrugated board, or other surfaces which is agreed upon for testing.

Your comments will receive careful consideration at a meeting of the responsible technical committee,1 which you may attend.

Identification number of the company: The resulting means and con?

The mass of the roller shall be 6 45 g [4. V3654 first verify your email before subscribing to alerts. During storage, panels should be protected from damage or contamination. The razor shall be held in position using side plates.

Between laboratories Between testers Between rolls Residual 0. The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the round end of the panel.

The surface shall be a true cylinder void of any convex or concave deviations. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.


Good cohesion is necessary for clean removal. Standards Subscriptions from ANSI provides a astj, multi-user solution for accessing standards.

One company reports that, with care, the between laboratory standard deviation and the residual including within roll standard deviation may be higher or lower than reported here, depending on the tape type and manufacturer.

The panel is mounted vertically, a standard mass is attached to the free end of the tape and the time to failure is determined. Combining values from the two systems will result in non-conformance with the standard. The use of an elevated temperature during test tends to reduce the duration of the test.

ASTM D shearing tester Cell Instruments Co Import Export

Please first log in with a verified email before subscribing to alerts. This may or may not relate to the ability of the tape to adhere to other surfaces. You may delete a document from your Alert Profile at any time. This standard is not included in any packages.

Subscription pricing is determined by: Only the sellers and buyers responsability is involved in case of dispute.