AUTRONICA BS-100 PDF

BS loop interface – BSD AutroSafe interactive detection system. Product datasheet. P-BSD/CGB, Rev. D, Protecting life. Products 1 – 20 of 33 Autronica BS , BS 90 and BS 60 fire alarm systems supplied, programmed and serviced. 3. Autronica Fire and Security AS. Contents. Please observe! This handbook contains installation instructions for fire alarm system BS DYFI ready designed.

Author: Zulkilabar Gojind
Country: Kenya
Language: English (Spanish)
Genre: Marketing
Published (Last): 18 June 2009
Pages: 401
PDF File Size: 16.97 Mb
ePub File Size: 10.51 Mb
ISBN: 237-9-98965-421-8
Downloads: 75894
Price: Free* [*Free Regsitration Required]
Uploader: Maumuro

Bend it and guide it into the printer paper slot in the lower end of the printer.

S and S are used for the setting of the reset number of the loops. Locate the ribbon cassette adjusting wheel side first, and then the other side. Image not available Photos not available for this variation. Resume making your offerif the page does not update immediately. Minimum monthly payments are required.

On optional printer, all; events and changes of status are printed.

BS-100 loop interface BSD-330

Cause and effect, and message data stored in nonvolatile memory with on-site changing capability. Report item – opens in a new window or tab.

When a loop is set in this mode, the alarm level ALI is changed so that the detector will react much quicker than standard: Please contact us via messages if you have any questions and we will be happy to assist you with any queries. Remove the empty autroncia by releasing the locking clip on the righthand side of the paper roll shaft, and pull the shaft out to the other side.

  ACIDO URSODESOXICOLICO PDF

Add to watch list. If you want to return an item, It must be in exact original condition it was sent. Monitoring of autronixa circuit changed. We are looking forward to distribute our used products with only economical price. Manual call-points give alarm with minimal delay.

Prewarning from a BS control panel autrknica registered on the relevant BS control panel and on the BS control panel. All our item should be as described in the item listing. Contact the seller – opens in a new window or tab and request a postage method to your location.

Changing of output controls and alarm outputs require password level 2 service level. The change must be typed as a three digit number the control output number. All disabled loops must be restored after ending the servicefunction. The last 10 alarm outputs will appear in the display as previously described. You are covered by the eBay Money Back Guarantee if you receive an item that is not as described in the listing.

The current stored analogue zutronica of the detector equal to ATS value. Beep codes Usual use of codes Code 0: Password level 1 bss-100 for changing display and printer texts.

null | BS-100 DYFI – Fire Alarm Engineers

Image not available Photos not available for this variation. We promise to provide the best service for our customers. Learn More – opens in a new window or tab Any international postage is paid in part to Pitney Bowes Inc. Please make sure that you check your address twice on eBay and Paypal for shipping. Refer to eBay Return policy for more details.

  FICHE APCE PDF

Learn More – opens in a new window or tab. Skip to main content. We do not accept returns because the wrong item was purchase or the buyer change their mind. See all condition definitions – opens in a new window or tab.

ASAP on 2-wired current loop.

BS DYFI – Fire Alarm Engineers |

Do not operate any bs-00 of DIP-switches with a pencil! The display picture above shows the first 8 control outputs related to this address. We accept offers from buyers. Only the sounders connected to the control panel which registered the fire alarm will be activated. Skip to main content. In case of power failure. Add to Watch list Watching.

Example of switch settings on DIP-switch S All new data bs-1000 now be stored in the battery-RAM and will remain in the system even in the event of a power failure.

Replace the printer and ribbon cables and set the power up. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list. Disable controls password protected. Default delay autroonica is 10 min.

Posted in Sex