BREMSHEY ORBIT PLUS MANUAL PDF

You can find the manual for your Bremshey Cross Trainer below. Bremshey Orbit Ambition Cross Trainer · Bremshey Orbit Control Cross Trainer · Bremshey. Check the reed sensor also known as the speed sensor. It is located on the front roller pulley. It is mounted to the frame and looks like a small. 18TSFC_Star Fit C HR i-Plus Crosstrainer_OMpdf . _Bremshey Orbit Ambition C_User Manual. pdf. MB.

Author: Tajas Tajora
Country: India
Language: English (Spanish)
Genre: Politics
Published (Last): 11 December 2016
Pages: 10
PDF File Size: 5.85 Mb
ePub File Size: 17.35 Mb
ISBN: 824-1-35808-770-7
Downloads: 90842
Price: Free* [*Free Regsitration Required]
Uploader: Malkis

Replacing the drive belt Type 1 1.

Manual – Bremshey Orbit Control Cross Trainer

The covers can now be removed. Turn the potentiometer shaft to obtain the correct setting and place the potentiometer back to the lift motor. Calibration parameters of User Interface are not valid.

This is because the components that have the most affect on the parameters are on the frame and thus bremshy EEPROM will have more accurate parameters for the new combination. Push the flywheel slider c down with a screwdriver and the release the outer cable sleeve d from the servo-motor securing point.

The recommended tension should be set so that with firm pressure the drive belt can only be deflected in one direction by approximately 3 mm bremshsy the point shown. Models with foot tube height adjustment.

Manuals for Bremshey Cross Trainers

Mechanics and Electronic Functions NB! In order to do this it will be necessary to disconnect the foot tube from the rear drum axle. E7 Instruction in the pljs manual: Type 2 transmission 1. These values can not be reseted Please refer to chapter 5 Please refer to chapter 5 Please refer to chapter 5 for closer details about brake calibration parameters.

  EDWARD ABRAMOWSKI PDF

Now reattach the floating tension arm spring so that the wheel is now applying pressure to the drive belt. If the noise has significantly higher frequency it ornit likely to be caused by a damaged front or rear roller bearing.

Lower board memory is damaged and the lower board needs to be replaced Please note that the ergometer can be used normally even it gives this error during start-up. Lift motor calibration is needed if any of the following has taken place: However, failure within the lrbit set or the meter can also be a cause. Speed sensor cable disconnected Meter cable has a poor connection at some point Magnet missing from the front roller pulley Front roller not rotating at all due to loose drive belt Check the distance between the speed sensor and the flywheel and ensure that the prbit sensor is properly attached to the motor frame.

Remove cap from the centre of the right-hand side drum cover. It compares the parameters that they are matching and are within preset limits see Table Check all intermediary wiring bremsjey.

Following question will be displayed on the screen: Bremehey software stores the calibration parameters in two separate places: Following question will be displayed on the display: If there is a presence of lateral fluctuation during rotation this may cause belt misalignment and lead to noise problems. To do this, remove all screws.

  IGOR RYDZANICZ ZAPIS KONSTRUKCJI PODSTAWY PDF

“service manual”

Replace the separating bush and then re-fit second bearing as above. Unscrew end from the bremshfy shock, at canister end A, insert M8 lock washer and reinstall shock. Check sensor magnet See section 2 No Brmeshey pulse 1. If a user complains that either of these settings are incorrect or a new servo-motor is fitted the following procedure should followed. Un-plug main power supply. Action to rectify 1. Rotate the drum in the opposite direction simulating reverse motion in use.

The primary intention of this Pluus Manual is to enhance the reader’s knowledge of the structures of the Tunturi bike ergometers E30, E40, E45, E60, E80 and E85 and Tunturi fitness bike F30 autumn onwards.

The lift motor has been removed from the frame The actual and the displayed elevation angle does not match 1. Bremshey EMS x 2.

If the noise has significantly higher frequency it is likely to be caused by rotating parts, i. The first one, Settings menu, is a public menu available also to the end user and accessed via normal menus under user settings.