CISCO EIGRP COMMAND AND CONFIGURATION HANDBOOK PDF

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE . interface configuration command to instruct EIGRP to use the received . Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network. Cisco Nexus Series NX-OS Unicast Routing Configuration Guide, .. The { ip | ipv6} passive-interface eigrp command suppresses neighbors from forming.

Author: Nikole Kejas
Country: Venezuela
Language: English (Spanish)
Genre: Technology
Published (Last): 18 January 2011
Pages: 108
PDF File Size: 15.96 Mb
ePub File Size: 1.43 Mb
ISBN: 653-2-62663-240-2
Downloads: 27234
Price: Free* [*Free Regsitration Required]
Uploader: Faull

Router config-router passive-interface default Prevents the sending of hello packets out all interfaces. Without it, an administrative distance of 5 is automatically applied to the summary route.

Austin configure terminal Moves to global configuration mode. Houston config-keychain-key key-string tower.

Inbound and Outbound Distribute List Route Filters Figure shows the network commxnd for the configuration that follows, which demonstrates how to configure inbound and outbound route filters to control routing updates using the commands covered in this chapter. Return to Beginning Previous Section.

EIGRP Configuration With Packet Tracer ⋆

Both the routes have an AD 90 and metric and are listed on two separate lines. Houston config-keychain key 1 Identifies the key number. Topology entry for Creates a standard ACL number 20 and explicitly denies the The list is pretty short:. Austin config-if ip authentication key-chain eigrp susannah.

Router config-router network Austin config-keychain key 1 Identifies the key number. Houston config-router eigrp log-neighbor-changes. Houston config-router key chain eddie Identifies a key chain name, which must match the name configured in interface configuration mode. Austin config-router key chain susannah. No neighbor adjacency will be formed.

  IMPROVVISO OP 90 N2 SCHUBERT PDF

You can use the show ipv6 protocols command to list all EIGRPv6-enabled interfaces including passive interfaces. Houston config-router network Router config-router distribute-list 2 out. Cosco of the most common problems associated with EIGRPv6 probably is that it is not enabled on an interface.

But we have included the explicit no shutdown command in router configuration mode to make sure EIGRPv6 works even if you happen to use an nad IOS version to practice the example. As a result, networks R1 configure terminal Enter configuration commands, one per line.

Change number of multiple routes to same subnet router configuration cpmmand. The rest of the configuration simply enables EIGRPv6 on all interfaces using the ASN to associate with the interface, using the ipv6 eigrp asn command. The subnet has one successor, which has an FD feasible distance of R1 show ipv6 route Houston config-router no auto-summary. However, if the parameters do not match, the two routers do not become neighbors and do not add each other to the EIGRPv6 neighbor table, listed by the show ipv6 eigrp neighbors command.

For instance, you could have two routers advertise the same network— The Hello messages enable routers to discover each other and also contain some parameters. HULL config access-list 30 permit With the maximum-paths router configuration handobok, up to 32 equal-cost entries can be in the routing table for the same destination.

Houston config-if ip authentication mode eigrp md5. cjsco

It can be applied to external type 2 and external type 1 routes but not to intra-area and interarea routes. Router config router eigrp Creates routing process Router config-router network The first highlighted subnet The verification and troubleshooting examples in this section will all use the topology shown earlier, composed of routers R1, R2, R3 and R4.

  DIME QUE SI ALFONSO ESPARZA OTEO PDF

See All Related Articles. Austin config-if no shutdown Enables the interface.

When you enable EIGRPv6 on an interface using the ipv6 eigrp asn command, the router would start discovering neighbors off that interface. The feasibility condition dictates that the reported distance the composite metric reported by a neighbor to reach a subnet is better lower than the currently best metric anv metric to reach the same subnet.

EIGRP Configuration| Step By Step Guide

Houston config-keychain-key accept-lifetime The subnet is reachable via next-hop link-local IPv6 address FE Creates an incoming global distribute list that refers to access control list ACL handbooi. We will use the topology consisting of four routers as shown configuratiob Figure for this example. We have used the number 1 for the ASN on all routers. The FS feasible successor is a route that meets the feasibility condition and can potentially become the successor route if the successor route fails.

Sample Chapter is provided courtesy of Cisco Press. Houston config-if no shutdown Enables the interface.

13-4 EIGRP for IPv6

Router config-router distribute-list 5 out ospf 1. Austin config-router no auto-summary Disables auto-summarization. A basic requirement of link-state routing protocols is that routers in an area must have identical LSDBs. The second highlighted subnet Enables manual summarization for EIGRP autonomous system on this specific interface for the given address and mask.