DESIGNJET T1300 SERVICE MANUAL PDF

Print from a computer using the Embedded Web Server or HP Utility (T series). free Web service makes it easy to access and print large-format documents . It is possible to assign a manual IPv6 address to the printer, using the front. This Service Manual contains information necessary to test, calibrate, maintain and service the following: HP Designjet T 24inch; HP Designjet T 44inch;. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration.

Author: Metaur Zulkigul
Country: Gambia
Language: English (Spanish)
Genre: Science
Published (Last): 17 May 2018
Pages: 83
PDF File Size: 19.96 Mb
ePub File Size: 11.76 Mb
ISBN: 803-1-31487-298-5
Downloads: 78924
Price: Free* [*Free Regsitration Required]
Uploader: Zulumi

Carefully pull the Scan-Axis Motor out of the product 10 mm until you can rotate it approximately 30 degrees counterclockwise. Tilt the Right Starwheel Lifter sufficiently to disengage the left attachment lug.

Lubricate the scan axis. There is a setting available that enables you to decrease the resolution for each print mode to dpi. Test printhead separately You are recommended to test the printheads individually to find the failing printhead. Contex Library failed to load Corrective action: USB Cable not connected Corrective action: Leave the sensor to one side to remove the collar Remove the collar by sliding it in the direction indicated Installation Installing the Right Collar is the same as the removal procedure, however care must be taken with the Cable and Sensor of the Scanner Position sensor.

Reboot the Product Try to upgrade the firmware again, for more information, see Appendix B: The product performs a series of movements numbered from 1 to Remove the from the product. Remove the two T screws that secure the Media Lever attachment plate. Slide the Belt Assembly out of the attachment on the Carriage Assembly.

  GILLIAM AUTISM RATING SCALE GARS PDF

A message will appear advising you that you will need to load the Calibration Pattern into the product. Leave one end of the roll cover resting on the floor.

Disconnect the cable connector as shown. Serviec Cutter Mode The purpose of this utility is to improve the cut quality for some papers that present some cut-quality problems straightness problems using the normal mode.

Close the Scanner or Window. Page Press Desognjet. Replace one component at a time and check whether the error desigjjet gone before replacing another component.

Remove the cables indicated from the cable ties. Disconnect the Scanner Position Sensor from the cable. Therefore, you are recommended to proceed in the following order. Loosen the T uncapping screw sufficiently so you can manually move the Carriage Assembly in step Left Roll Guide Removal Switch off the product and remove the power cable.

HP DesignJet T in Printer User Guides | HP® Customer Support

Remove the Micci2 and Power cables from the clamps; remove the taping that hold seervice cables. Press OK to end the test. The Control Panel prompts you to feed the original. Remove the deflector assembly. Remove the media from the product before proceeding with the procedure. Page 53 System Error: Page Wait until the scanner validation test has completed.

Page Primer motor In the Diagnostics menu, sesignjet to Service Station and press on this menu option. EE Box on page Bi-stable Springs These parts should not be replaced by customers.

Page 31 Pull the blue handle up and toward you to release the Carriage Cover. Place the Ink Supply tubes on top of the product as shown here. Be very careful not to scratch the Encoder Strip with your fingernail or any other object. Full Bleed Foam on page Remove the screw connecting the roll cover to the product on the right. When you reinstall the full bleed foams, take care to correctly seat them to avoid possible damage to the Carriage Assembly Hard Disk Drive Removal and installation Window Removal Switch off the printer and remove the power cable.

  ANGEOLOGIA DEJIN PDF

Modify your browser’s settings to allow Javascript to execute.

HP Designjet T790 / T1300 / T2300 series. Service Manual

The Touch Control Panel then prompts you to release Piston 0. Remove the Pinchwheel Alignment Tool from servicce product. Fit the basket supports to the stand legs, one to each leg. Remove screw and straight bushing.

Turn the product back on. Page The Touch Control Panel lock is reset. Ensure that the Ink Cartridge is the correct color for that slot.

HP DESIGNJET T1300 ePrinter series Service Manual

Make sure the bushing and screw do not fall into the product’s cavity by placing your hand underneath as you remove it. If printhead alignment cannot be completed, try the following.

Press on the Replace Printhead tab. Page 91 Entering the Diagnostics Menu Make sure the product is switched off with the Power key on the side of the Touch Screen Panel, and not with the power switch on the back of the product. Then a screen is shown where the zero position sensor is checked. To clean the drive roller and overdrive, see