EN 10243-1 PDF

DIN EN – Free download as PDF File .pdf), Text File .txt) or read online for free. Find the most up-to-date version of DIN EN at Engineering Buy DIN EN STEEL DIE FORGINGS – TOLERANCES ON DIMENSIONS – PART 1: DROP AND VERTICAL PRESS FORGINGS.

Author: Arasar Tamuro
Country: Chile
Language: English (Spanish)
Genre: Environment
Published (Last): 28 September 2007
Pages: 187
PDF File Size: 11.30 Mb
ePub File Size: 3.8 Mb
ISBN: 992-3-17958-646-6
Downloads: 43908
Price: Free* [*Free Regsitration Required]
Uploader: Kajigami

Where more restrictive tolerances are required for application to individual dimensions of thickness, supplementary operations are involved.

For centre-to-centre dimensions greater than 1 mm length, tolerances from Table 1 or Table 2, with equal plus or minus dispersions, shall be applied. While grade E close tolerances may be applied to all dimensions on one forging, it is more economical to apply them only to those specific dimensions on which closer tolerances are essential.

BS EN 10243-1:1999

Where restrictions in deviations of form have been agreed, these will be to ISO and noted on the drawing. By further movement to the right, the correct tolerance is found under the appropriate vertical column heading for the dimension concerned wherever possible the greatest dimension of length, width or height see 5.

If the category of steel used is M1, the same horizontal line is followed further to the right. Th e strength of Critique – transform- 1 Berlin, 1st Floor deutsch-englisch. Straightness and flatness tolerances are to be found from Table 5 according to the greatest length or greatest width dimension of the forging.

On forged surfaces which are not machined subsequently, scale pits and surface dressing shall be permitted to a depth equal to one-third of the total value of the thickness tolerance. Tolerances for the maximum permissible extent of such distortion are based on the nominal diameter of the unforged stock in accordance with Table 6 and Figure Ost 1 71 english translation deutsch, francais, italiano Business.

Many instances of heavy die wear occur in which these tolerances are inadequate. The same method applies for the use of all tables according to the grade of tolerances required.

  LA BRUJERIA DEL FUTURO DOREEN VALIENTE PDF

These marks may be either sunken or raised. The permissible length of local deviation from the bar stock diameter or section adjoining a forged portion shall be up to 1,5 times the bar stock diameter or largest cross-sectional dimension, but with a maximum value of mm see Figure All forgings bear the CDP identification mark, unless a different wn Documents. Tolerances for fillet radii and edge radii are shown in Table 6 and examples of such radii are shown in Figure Worldwide Standards We can source any standard from anywhere in the world.

In such cases the minus tolerance is modified to allow for the formation of a square corner. Search all products by. This special procedure is not applied if larger tolerances will result from use of 110243-1 normal procedure as shown in 4.

BS EN – Steel die forgings. Tolerances on dimensions. Drop and vertical press forgings

This approach will ensure that optimum use is made of the forging process in fulfilling the purchaser’s special requirements at the lowest additional cost. Examples are shown of circular and non-circular forgings see Figure 2 and Figure 3.

The residual flash is measured from the body of the forging to the trimmed edge of the flash, as indicated in Figure Normally the tolerances for the greatest dimension of length or diameter of the forging will be applied but, if more 01243-1 tolerances are required, those for the specific dimension of the pierced hole may be used. Types of inspection documents PD A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the English versionSteel die forgings Tolerances on dimensions Part 1: Find Similar Items This product falls into the following categories.

C 45Category of steel used see 4. The tolerances are determined from Table 3 and Table 4 in accordance with the greatest thickness dimension of the forging. Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 34, an inside back cover and a back cover. Published on Jul View Download Ejector mark tolerances are 1043-1 independently of, and in addition to, any other tolerances.

  INS ONEC DZ BAC PDF

Permissible tolerances based on the greatest dimensions are usually obtained from the appropriate table Maximum length: Pieces executees a chaud sur marteaux-pilons presses verticales. They are not used for check measurements on the actual forging, but for tool construction when forging dimensions are not measurable.

To determine the category in which a steel belongs, the maximum permitted content of the elements in the steel specification shall be the values used.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. ISOTechnical drawings Fundamental tolerancing principle.

Your basket is empty. The enveloping shape of a circular forging is the circumscribing cylinder, the mass of which is calculated from the formula see Figure 2: Such special tolerances shall be 1024-31 between the supplier and the purchaser before the commencement of production. The BSI copyright notice displayed in this 1023-1 indicates when the document was last issued.

The first part of this European Standard applies to hot forgings in the delivery condition, made in carbon and alloy steels. Above 0,63 up to and including 1. This publication does not purport to include all the necessary provisions of a contract. To determine length, width and height tolerances, reference is first made to the appropriate category in the mass column.

Please download Chrome or Firefox or view our browser tips. Flatness tolerances relate to deviations of surfaces from the specified contour. They are best dealt with by consultation at the design stage and shall be agreed between the purchaser and the supplier. These two grades of tolerances are identified as follows: As a general rule grade F tolerances result in a cheaper forged component.

S3Type of steel used: