FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Tolkree Kajar
Country: Belgium
Language: English (Spanish)
Genre: Science
Published (Last): 13 December 2013
Pages: 71
PDF File Size: 8.78 Mb
ePub File Size: 19.34 Mb
ISBN: 668-2-84811-957-5
Downloads: 94514
Price: Free* [*Free Regsitration Required]
Uploader: Shakall

Possible Causes What to Check and Suggested Measures 1 Conditions for Compare the settings of the y codes y01 to y10 with those of the host communications differ equipment. FRENIC-Lift is an inverter lft to drive a three-phase induction motor hereafter called an induction motor and a three-phase permanent magnet synchronous motor hereafter called a synchronous motor for exclusively controlling elevating machinery. Using the optional multi-function keypad allows you to start and stop the motor, monitor running status, and switch to the menu mode.

Torque bias gain adjustment BTBG. Page 54 F codes: Page 21 Mounting the covers Put the front cover to the inverter case so that its bottom engages with the hinges provided on both sides of the case.

Fuji Electric FRENIC-Lift series Instruction Manual

Otherwise fire or an accident could occur. The first letter is an alphabet that identifies its group and the following two letters are numerals that identify each individual code in the group.

Grounding terminals G Be sure to ground either of the two grounding terminals for safety and noise reduction. Page 59 H codes: For the inverters with a capacity of 22 kW or below, wait at least 5 minutes; Page 60 y codes: To mannual it follow the steps listed below. Insulation Test A dielectric strength test will cause breakage of the inverter similarly to the Megger test if the test procedure is wrong.


CAN bus An abnormal communication with the main body of the inverter is detected when communication the CAN bus is used, and the inverter kift stopped.

Table of Contents Add to my manuals Add. Maximum speed F03 2 The reference torque bias follows the input voltage level on terminal [12]. Possible Causes What to Check and Suggested Measures manuzl No power supplied to the Check the input voltage, output voltage and lict voltage unbalance. Enter text from picture: Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances.


No part of this publication may be reproduced or copied without prior written permission from Fuji Electric Co. If any of the problems listed below occur, take an appropriate measure against them. External View And Terminal Freenic 1.

Name of option Function and application Insert an MC in the power source side of the inverter in order to: Doing so could cause burns. Put the front cover back in reverse order of. Use them in accordance with your system requirements. When the replacement is necessary, contact your Fuji Electric representative. Using this adapter greatly Take an attention for this structure to connect wires to main output secondary terminals.

Release the mechanical brake. Set up L02 for correct data.

Speed monitor Select by E48 3: Page 24 – Terminal arrangement and screw specifica The operation level and thermal time constant can be set. Tuning procedure What follows gives liff a tuning procedure of the inverter for mmanual motor using a multi-function keypad option. Page 77 [ 16 ] Run operation error Problem You incorrectly operated the inverter.

Page 18 1 Remove all of the base fixing screws from the top and bottom of the inverter.


Page 82 [ 25 ] Over torque current Problem Reference frenkc current became excessive. Icons The following icons are used throughout this manual. All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders.

Removing the cable guide plate Before to proceed, remove the terminal block cover as shown below left. Remove the screw fastening the cable guide plate, and pull out the plate. Page 31 These are provided for the DC link bus powered system. Frenicc to Chapter 2 Section 2. Torque limit time 0. Each part of the product has its own service life that will vary according to the environmental and operating conditions. Do not hold covers or individual parts only.

In no event will Fuji Electric Co. Chapter 6 Troubleshooting 1 First, check that the mxnual is correctly wired, referring to Chapter 2, Section 2.

To manial the manual completely, please, download it. Driving gener- When high starting torque is required or quick acceleration or deceleration al-purpose motor Selecting is required, select an inverter with a capacity one size greater than the inverter standard. Page 17 When employing external cooling At the shipment time, the inverter is set up for ffenic inside your equipment or enclosure so that cooling is done all internally. Install FRENIC-Lift in compliance with the local regulations, Described below for an example, a procedure shows an installation of the inverter in compliance with regulations in Japan.

Page 39 Table 2. Do not use a circuit breaker with a capacity exceeding the recommended capacity.