HIROBO SCEADU MANUAL PDF

Categories Parts fuel Parts Hirobo Shuttle Sceadu SCEADU MANUAL Ask question. Description. SCEADU MANUAL. Browse this category: Shuttle Sceadu . Categories Parts fuel Parts Hirobo Sceadu Evolution SCEADU SWM INSTRUCTION MANUAL MANUAL. Browse this category: Sceadu Evolution. Beyond Sceadu!! SDX 50HPM kit. This swashplate accepts 90°HPM,. °SWM, and °SWM linkage for all Hirobo 50/90 size models.

Author: Kajilar Zolokree
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Career
Published (Last): 6 November 2008
Pages: 218
PDF File Size: 18.95 Mb
ePub File Size: 15.46 Mb
ISBN: 258-6-97883-370-3
Downloads: 72328
Price: Free* [*Free Regsitration Required]
Uploader: Daira

Vintage RC Helicopters – Hirobo Sceadu

Final fuel tank assembly. If you find your end point much overmove the ball out one hole and start secadu. Aligning servo arm and throttle arm. When the left stick is moved across to the right, the servo should pull or move the control rod forward moving the tail pitch plate outwards away from the tail case.

Once I started breathing again, post flight inspection revealed the clunk stuck at the front of the main tank. Put two 32mm screws through the left frame and make sure they go through the holes in the lower tail drive bearing block and into the right side frame.

hirobo sceadu evo 30 combo set up sheet for use with mrc |

Stabilizer Blades feature adjustable weights and are secured to the flybar with dual set screws. Hardened hex drivers won’t wear and strip out bolt heads, and the inline amp meter makes setting up control throws without binding very precise.

Tail Boom Mounted Servo for tail control is standard equipment – Also available a 5mm control rod to replace the 2 mm existing rod. A belt driven tail utilizing a lower friction belt is standard equipment. It’s the ultimate user-friendly drone- The fastest, easiset and most economical wa The EVO did every maneuver we could throw at it. A few minor changes were later made to the EVO; the rotor head was changed to the FZ-IV, featuring a machined aluminium centre block and had the flexibility to be configured hirbo meet pilot’s proficiency level.

  ELFORUM.RO CARTI PDF

Hirobo Shuttle Sceadu Evolution Instruction Manual Page 48

EVO 50 early version. Photo 4 shows the tools I have on hand. New larger Bearing are used to support the collective lever system for complete “slop” free smooth control for any flight envelope. This bag isn’t labeled as step 5, but it’s the one that contains the black drive belt as noted in the instructions. I like these tail pushrod guides!

Once throttle hold was set, Ihrobo activated throttle cut to make sure it would kill the engine. Make sure the main blade grips are oriented as shown in photo 28; then mount the see saw to the main rotor hub with 8mm hex screws and washers. If you are going to remove paddle weight start by taking out the lead weights. Mount the servos in the appropriate slots, mind the spine orientation and use the servo plates with no eyelets on the collective servo.

SCEADU MANUAL

Locktite and tighten the tail case screws. Two flights, two autos, no broken parts; I decided to call it a day.

Turn off the receiver, set the switch to heading hold mode and turn on the receiver. Most of the steps consist of mechanical drawings and are interspersed with helpful notes, but the builder is left to decide on his own assembly sequence.

I found it easier to use a screw to cut starter threads in all the places that balls are going to be installed; they can be somewhat of a chore to start the screw with the ball on it and you can avoid stabbing yourself with a screw driver. This does two things. I got mm sticking out of either side.

The phenomenon has become common enough for most of us to refer to them as a piston punch tool. The Proto-Z is a Blast of micro-sized fun! If you are familiar with my reviews you have seen me use a caliper and the Vario pushrod nubs to make perfect pushrods. Grease a set of radial bearings and install them on the hub side of the grips.

  KAMPUS WONG ALUS PDF

Insert the metal main rotor hub into the plastic head block and make sure the bolt holes are aligned.

To further help you finish your model, visit our website at www. They are adjustable and easily removable should you need to change the tail boom.

We also recommend removing the baffle in the muffler if tuning is difficult or power seems to be low. The Futaba wheels have concentric circles with distance from center marked on them, so if you have these on hand, it makes life a bit simpler. No info currently held on these later versions. On a breezy day the EVO is still rock solid. If they are 90 degrees apart on the shaft you used the wrong hole and it will throw your final linkage measurements off. Mount the servo using the lower set of holes and mount a ball 17mm out on the arm.

Mount your receiver and battery. If your engine starts running rough after running well for a period of time, do not adjust the needle valves immediately. Install the engine mount bolts and if you are going to use one, the remote glow plug adapter at this time. New larger shaped fins effective in fast forward flight when decals are applied or ideal for 3D flying with their decals removed.

Then put the last bearing race on the spindle. Super strong, super light. Trim the servo horn so it does not interfere with the aileron servo operation.

Seagull Models introduced this biplane early on inand SIG mfg. Hirobo has neatly packaged everything in bags that are numbered to correspond with the assembly steps. With only a very few exceptions, you open a bag, assemble all the parts in that bag and move on to the next step.