HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. Fri, 12 Oct GMT ht12e encoder ic ht12e datasheet pdf – HT12E is an encoder integrated circuit of. 2 12 series of encoders. They are. HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the.

Author: Samurisar Nirn
Country: Barbados
Language: English (Spanish)
Genre: Video
Published (Last): 24 October 2006
Pages: 382
PDF File Size: 9.24 Mb
ePub File Size: 2.25 Mb
ISBN: 558-3-96421-638-6
Downloads: 41532
Price: Free* [*Free Regsitration Required]
Uploader: Shakataxe

TL — Programmable Reference Voltage. It is mainly used in interfacing RF and infrared circuits. As soon as TE returns to high, the encoder output completes its final cycle and then stops. It is very important that your Decoder should also have this same address for them to talk to each other. This high-density System-in-Package SiP integrates controller, power switches, and support components.

The IC is has a wide range of operating voltage from 2. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

HT12E Datasheet

You can know to set up the HT12D after this from here. They can also be connected to switches to manually send and receive data. Interface SD Card with Arduino.


Arduino based GPS receiver. Virgin Galactic — Commercial Space Flight. Simply put, HT12E converts the parallel inputs into serial output. fncoder

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Transmission enable; active low. The Encoded 12 bit output data can be obtained from this pin. Interface GPS with Arduino. If you want security you can connect any of the 8 pins to 5V to make it high.

This oscillator can be used by connecting these two pins through a 1M Resistor. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

Choosing Motor For Robots. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

Supply voltage; 5V 2. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. SPI Module of Arduino.

So encorer you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. The encoded bit can be obtained from the Dout pin pin HT12E is an encoder integrated circuit of 2 12 series of encoders.

HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. Can range from 2. HT12E has ht112e transmission enable pin which is active low.


The primary function of HT12E is to encode a bit and send it out through the output pin. They are paired with 2 12 series of decoders for use in remote control system applications. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Connected to the Ground of circuit. Skip to main content. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

HT12E Encoder IC

Choosing Battery for Robots. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

This pin has to be connected to Ground 0V to enable the Transmission. What datashheet Web Browser. These 12 bits are divided into 8 address bits and 4 data bits.