HYPERTHERM HPR260XD MANUAL PDF

Hypertherm, HyPerformance, HyDefinition, LongLife and CommandTHC are trademarks of .. HPRXD Manual Gas – Revision 2. guarantees the Hypertherm quality you can count on. The HPRXD delivers superior bar ( psi) Manual gas console. 8 bar ( psi). ArcGlide, EDGE Pro, Hypertherm, HPR and Sensor THC are trademarks of Hypertherm, Inc. and may be When you see a safety symbol in this manual or on your machine HPRXD, HPRXD with a built-in.

Author: Nikoshura Zurr
Country: Djibouti
Language: English (Spanish)
Genre: Medical
Published (Last): 28 May 2018
Pages: 120
PDF File Size: 18.37 Mb
ePub File Size: 16.95 Mb
ISBN: 684-3-57907-822-1
Downloads: 28648
Price: Free* [*Free Regsitration Required]
Uploader: Kecage

All access and service doors and covers should be closed and properly fastened when the cutting equipment is in operation. Are the cut settings in the hypertherm manual fairly accurate? Number hyperterm welding and cutting systems in operation.

Particulates no more than 00 particles per cubic meter of air at a Size of 0. See the Specification section for and flow specifications. The Vinyl Siding Trim is a universal part that can be used in combination. Avant le coupage, retirer de ses poches tout objet combustible comme les briquets au butane ou les allumettes.

If electromagnetic disturbances are detected then it shall be the responsibility of the user to resolve the situation with the technical assistance of the manufacturer.

  LM319N DATASHEET PDF

Install this switch near the power supply for jypertherm access by the operator. Work table Connect the work table to an earth ground, in accordance with appropriate national and local electrical codes.

Allow room to open the top for servicing. Never use automotive anti-freeze in place of propylene glycol. Pacemaker and hearing aid wearers should consult a doctor before going near any plasma arc cutting and gouging operations.

Document Outline

Government Printing Office, Washington, D. See also Torch connections earlier in this section for torch lead connections to ignition console. Connect the hyperthfrm vent hose white. Electrical hazards Only trained and authorized personnel may open this equipment.

It is the responsibility of the equipment and site owner to test the air quality in the area where the equipment is used gypertherm to ensure that the air quality in the workplace meets all local and national standards and regulations. While is flowing adjust the supply regulator for the shield pressure to 8 bar 5 psi.

Hypertherm HPRXD Manual Gas Rev.3 manuals

Remove any combustibles, such as a butane lighter or matches, from your pockets before cutting. SGR Services de gestion des risques Title: The power supply can be moved by forklift hypsrtherm the forks must be long enough to extend the entire length of the base.

Never operate the plasma system unless the power supply covers are in place. Connect the power leads to the terminals of TB as shown below. Utiliser des affiches ou des panneaux. When the flow rate is constant and greater than Etiquete hyprtherm identifique con colores todas las mangueras de, para saber el tipo de que transporta cada manguera.

  DEMAG AC200 PDF

To reduce magnetic field hazards: Off-valve The off-valve consists of 5 solenoid valves, a manifold block and a wiring harness with connector. Use local exhaust ventilation to remove fumes from the air. Control your dog with your Smartphone.

HyPerformance Plasma. HPRXD Manual gas. Instruction manual Revision 2 – PDF

Ignition console The ignition console uses a spark-gap assembly. The pump will run continuously while 8 is pressed. The highvoltage, high-frequency signal is coupled to the cathode lead and pilot arc lead.

There is a diagram on page for reference. The Hypernet PCB provides communication between components and is the source for the arc voltage needed for the torch height control. If the metalic sheath of the torch leads hpr260sd near any motor or drive or controller cables The time now is