IC 74166 DATASHEET PDF

Description: The NTE is an 8-bit parallel-in or serial-in, serial-out shift register in a Lead plastic DIP type package having the complexity of 4 — 28 December Product data sheet .. supply current VI = VCC or GND; IO = 0 A;. VCC = V. -. -. -. -. μA. CI input capacitance. -. description. The ‘ and ‘LSA are 8-bit serial shift registers that shift the data in the direction of QA toward QH when clocked. Parallel-in access to.

Author: Nataxe Sazil
Country: Fiji
Language: English (Spanish)
Genre: Finance
Published (Last): 7 January 2006
Pages: 366
PDF File Size: 19.46 Mb
ePub File Size: 5.77 Mb
ISBN: 590-7-71935-802-7
Downloads: 28290
Price: Free* [*Free Regsitration Required]
Uploader: Kazrakora

If you know you will need to use multiple shift registers like this, check that datssheet shift registers you buy can handle Synchronous Serial Input as well as the standard Synchronous Serial Output capability. The long arrow indicates shift right down.

It is referred to as a latch pin. No abstract text available Text: The arrow after C2 indicates shifting right or down.

In this example you’ll add a second shift register, doubling the number of input pins while still using the same number of pins on the Arduino.

Pins P3 to P7 are understood to have the smae internal 2,3 prefix labels as P2 and P8. T h e G ra p h ic E d itor offers ad van ced featu res such as m u ltiple h ierarchy lev els, syG rap h ic and T ext E d ito rs w ith the d elay p red ictio n featu re. Datashret manufacturer labels the data inputs A, B, C, and so on to H.

  DECRETO 6029 97 PDF

In which case, the microprocessor generates shift pulses. We have not looked at asynchronous loading of data up to this point. This needs to be differentiated from asynchronous load where loading is controlled by the preset and clear pins of the Flip-Flops which does not require the 741166. Previous 1 2 First, C3 for shifting parallel data wherever a prefix of 3 appears. It is either shifted datashset another integrated circuit, or lost if there is nothing connected to SO.

Iv waveforms below show both parallel loading of three bits of data and serial shifting of this data. After t 4 all data from the parallel load is gone.

Q8 is the only one used in these examples. This is because the code examples will be using the switches attached to the second shift register as settings, like a preference file, rather than as event triggers. There is more information about shifting in the ShiftOut tutorial.

The important factor is that it needs to be low around clock time t 1 to enable i loading of the data by the clock.

The Triangle pointing down indicates a tri-state device. If supplementing your Arduino with an additional 8 digital inputs isn’t going to be enough for your project, you can have a second CD pass its information on to another CD which will stream all 16 bits of information to the Arduino.

The internal logic of the SN74LS and a datasheett summarizing the operation of the control signals lc available in the link in the bullet list, top of section.

  2N3053 TRANSISTOR PDF

Arduino – ShiftIn

We use an asynchronous loading shift register if we cannot wait for a clock to parallel load data, or if it is inconvenient to dwtasheet a single clock pulse. The prefix 3,4 of internal label 3,4D indicates that M3 and the clock C4 control loading of parallel data.

Q7 is a pulse behind Q8 and Q6 is a pulse behind Q7. The Datashfet leads will have vias that go directly to the. SRG8 says 8-stage shifter. The CDB is a similar part except for asynchronous parallel loading of data as implied by the lack of any 2 prefix in the data label 1D for pins P1, P2, to P8.

It needs to be low a short time before and after the clock pulse due to setup and hold requirements. At the next positive going clock edge, the data will be clocked from D to Q of the three FFs.

Shift Registers: Parallel-in, Serial-out (PISO) Conversion

SN SN 7V 5. By parallel format we mean that the data bits are present simultaneously on individual wires, one for each data bit as shown below. Sometimes you’ll end up needing more digital input than there are pins on your Arduino. This is repeated for all 8-bits.