INSTALLATION DSC5010 PDF

Read this manual carefully and have your installer instruct you on your system’s operation and on which features have been implemented in your system. I have a DSC model alarm () and this installer code was . The Down and Dirty at unlocking a DSC Alarm with Installers. Parent Directory · PC Pager · PC Partition · PC v Demo User · PC v Installation · PC

Author: Mak Tojaramar
Country: Ethiopia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 20 April 2013
Pages: 31
PDF File Size: 17.83 Mb
ePub File Size: 8.26 Mb
ISBN: 518-5-33702-818-2
Downloads: 54246
Price: Free* [*Free Regsitration Required]
Uploader: Zuzuru

My installer of course will not give me the “installer code” which I need. There’s also an LED backlight. I suppose that means the lock switch disables the remote control, otherwise it could simply be in series with the indoor button. Before I disassembled the button cluster, I’d just short the wires and see what happens.

They must be putting an AC signal on the two wires and sensing the impedance at that AC frequency.

There’s one problem with it but I’ll leave that for another topic. Greetings, I’m new to this alarm stuff but very conversant on a technical level. There are two wires that go to ssc5010 Chamberlain Liftmaster garage door opener control. What is this old floor.

Re: DSC PC5010 – how to change Install and Maint codes?

I wanna install a second button in the garage anyway so will need to figure out. I’ll put a protection diode across the relay coil for good measure too. Tub pump air tube came off.

Short answer, shorting the two wires together will raise or lower the graj door -easy. Hopefully I’ve made this clear enough, I’m sure this has been done a hundred dsf5010.

  JURNAL PENYAKIT PROGERIA PDF

What I learned Today: DSC Alarm Panel Installer Lockout. (PC)

Here are two with sources: Whether I have to actually get licensed after all this I really don’t care. The logic in the motor control will cycle through down-stop-up with each press. The output I’m planning on having drive a small relay. There must be a circuit breaker that will disconnect power for that ladder job. The panel will insyallation default if the battery is used. If I want to lock the door out, I kill power to the whole unit.

Where I live graj door openers are required by code to be permanently wired into the electrical service. Not sure why they didn’t just use resistors though.

A family member could have come installatiin and opened the door while I was up on a ladder in the door travel area thinking the opener was disabled by the lock function.

My current Genie models have a second button that turns the light on. You may not post new threads. I’ll power down the thing and pull the cluster apart.

Index of /manuals/DSC/Intrusion Panels/PC5010-Power832

The lock function is not only useless, it is downright dangerous. Aprilaire – Basic Solenoid Question. What is this button cluster? AC power must be used to power the panel. Dsc5100 4 – Apply AC power to the main panel. When I found that out, quite by accident, I damn near had a heart attack.

To confuse matters further there are 4 contacts on the opener itself which are shared between the cluster, photocell and beam. Trying to instal,ation up tire changer motor to switch.

  BILLY BUNTER OF GREYFRIARS SCHOOL PDF

How to install and programme DSC to open and shut my garage door

Okay, I took the keypad for the graj door opener apart last night. Logged dknull Security Guru Posts: BB code is On. Real Knowledge From Real People.

Please login or register. There are only two wires going to the button cluster. Anyway, just thought I’d share with others whom may have a Chamberlain graj door opener. I’m probably over-thinking this being an engineering type. But that’s just me.

Yes, that’s how it works. October 08, Find all posts by MrRonFL. My opener has two buttons, one opens the door and the light comes on automatically and the other turns on the light without opening the door.

It certainly isn’t clear from the installation manual. The main button will be zero ohms, and the other two will be higher values. The programming for PGM2 is described in the installation manual, which you can download from this website – see the Online Manuals tab above. If nothing else, I now know how to make my own full-function keypad. I was told I’m lucky that the Installer code of wasn’t locked out. I think I still might do that even though I also have a lock button. If you don’t have any wires to PGM2, you’re good.

Programming suggestions welcome here.

I believe 1uF and 50uF.