INTERSEAL 670HS MSDS PDF

INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Tojanris Tygorisar
Country: Indonesia
Language: English (Spanish)
Genre: Science
Published (Last): 19 July 2009
Pages: 473
PDF File Size: 9.13 Mb
ePub File Size: 9.81 Mb
ISBN: 399-2-61382-239-7
Downloads: 51907
Price: Free* [*Free Regsitration Required]
Uploader: Arashilmaran

Be the first to write a review for this product! Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service.

Premature exposure to ponding water will cause a color change, especially in dark colors. Sagola or Air texture gun fitted msdds a mm nozzle.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

A surface profile of mils microns is recommended. However, these phenomena are not detrimental to anti-corrosive performance. If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS.

Application should then be to a suitably primed surface. Varnish Innterseal Water base. Level of sheen and surface finish is dependent on application method. Accumulated dirt and soluble salts must be removed. However, it can be used over suitably primed surfaces. Mouse over image to zoom.

Brush Typically mils microns can be achieved Roller Msdw mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates.

  DUSUM SANGYE PDF

However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used.

Low or high temperatures may require specific application techniques to achieve maximum film build. Do not thin more than allowed by local environmental legislation.

In common with all epoxies Interseal HS will chalk and discolor on exterior exposure. Preferred application is by a suitable large tip hopper gun e. Puddles, ponding and accumulations of water must be removed.

INTERSEAL HS – PART B (REGULAR) – L ( :1)

Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. Please consult International Protective Coatings for alternative recommendations.

Further information is available from International Protective Coatings. Dry bristle brushing will normally be adequate for accumulated dirt.

Typical thicknesses will be between milsmicrons. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by brush to ensure thorough wetting out of the substrate by Interseal HS.

Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate. Once the unit has been mixed it must be used within the working pot integseal specified. Typically this would apply to C or D grade rusting in this standard.

Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings. The surface to be coated should be clean, dry and free from contamination.

  HD44780 2X16 PDF

Consult International Protective Coatings for further details. With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Certification is for tanks greater than gallons Alternatively, a broadcast method of application can be used. It is also possible to apply to damp surfaces in some circumstances.

Soluble salts should be removed by fresh water washing. Always mix a complete unit in the proportions supplied. A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. Avoid using a mixture of application methods whenever possible. Loose or flaking coatings should be removed back to a firm edge. Trowel or roller can be used for small areas. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner.

Press and move to zoom. Surface preparation The performance of this product will depend upon the degree of surface preparation. For msdds to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. When applying by methods other than airless spray, the required film build is unlikely to be achieved.

NSF Certification is for tanks greater than 670h Prior to paint application all surfaces should be assessed and treated in accordance with ISO