Irganox is a high molecular weight phenolic antioxidant. CAS# Click here for quote or sample. Irganox® highly efficient, non-discoloring, sterically hindered primary phenolic antioxidant stabilizer that protects organic substrates against. Get instant access to Irganox® technical datasheet. It is a highly efficient sterically hindered phenolic primary antioxidant which provides processing and.
|Published (Last):||16 August 2007|
|PDF File Size:||1.57 Mb|
|ePub File Size:||2.55 Mb|
|Price:||Free* [*Free Regsitration Required]|
As evidenced in Fig. FTIR revealed the growth of form I and the transformation of form III to the liquid state even if the band characteristics of this liquid state is very close to that of form I. AFM is thus a convenient tool for this research. This kind of effect of the probe at a nanoscale was observed by Perkins et al. However, UL assumes no responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer.
The lowest adhesion values were obtained for the crystallized AO regions. However it was difficult to exclude the previous melting of the form II because it was shown that, at this heating rate, forms I and II have very close melting temperature and enthalpies of fusion.
The implication of melting of form III needles and its recrystallization into form I on the surface energy was suggested, by hypothesizing that some imperfect small crystals can melt at a little lower temperature than that of the onset melting However this melting of form III is concomitant to an exothermic peak characteristic of a recrystallization as observed on DSC thermogram.
Octadecyl DI-tert-butylhydroxyhydrocinnamate | C35H62O3 – PubChem
Do you want a quotation or have a question about 176 ‘? Depending on the polymorph that crystallizes, the impact on surface properties and leaching might be different.
We observed profiles of the adhesion perpendicular to the melting front of the AO crystal. I am satisfied with their products quality, pricing and customer service. Keep it up and wish you all the best for future challenges. In a previous paper, 26 the aging behaviour of a catheter after a discharge nitrogen plasma treatment was studied.
Increasing the temperature of several degrees had a deep impact on the phase transformation kinetics: The growth of the characteristic band of the melting state was observed. Irganox Worldwide Suppliers of Irganox https: A before melting B at the beginning of melting C for an almost melt needle.
However, by using the new results presented here, we can suggest another explanation for this aging: It should be noted iryanox the onset of the melting temperature for form III was found at Irganox Irganox Worldwide Suppliers of Irganox https: The enthalpy of fusion of the form III which melt at lower temperature than forms I and II was greater than those of the two other forms Table 1.
In general, personally speaking, I am satisfying with your performance in our needs and I am sure that we will continue our cooperation. We may suppose it lrganox a transition between form II and form I for the following reasons: We normally respond within 2 hours.
Irganox® by BASF Dispersions & Resins – Paint & Coatings
However our data tend to prove that form II is converted into form I before form I melts. By studying adhesion force image Fig. It is indeed well known that surface properties will condition the device biocompatibility and irganoox bioadhesion on it. The initial AO crystal structure is thus strongly modified during these thermal treatments.
Form I should be a metastable form for temperatures lower than the melting temperature lrganox form III. This website provides links to other websites owned by third parties. No melting phenomenon occurred during this process as shown by the adhesion measurements Fig. We estimated the transition temperature using the following relationship, which was used quite successfully by other authors: Chemist Analytical Development Lab Co-ordinator.
This may be the high-temperature stable form before melting; however, as the forms I and II have very close enthalpies of fusion, it is thus not trivial to conclude about a monotropic or enantiotropic transition between them. The sample was heated slowly. The content of such third party sites is not within our control, and we cannot and will not take responsibility for the information or content.
Numerous papers have been published on the solid-state phase transitions: As shown by the adhesion measurement, no liquid areas were detected during the first moments of the process images 1—13 from Fig. Any patent infringement and resulting liability is solely at buyer risk.
We’re sorry, but the industry you have selected is not currently available in your chosen language.
Clearsynth has excellent products with fantastic customer service. However, the determination of such relations might be very difficult, because some metastable forms are very stable-like at ambient temperature for kinetic irgamox and because these transitions can thus be very slow and difficult to put into irgannox by differential scanning calorimetry DSC. Spectra of form I and melt powder are given as references.
Received 21st OctoberAccepted 8th December The sample was then heated up to The heating rate used was a quick one till the form III melted. Polymorphism is not always easy to understand and to predict and its comprehension needs the use and association of different analytical techniques. Key product areas of formulation additives, rheology modifiers, light stabilizers, and antioxidants significantly enhance the BASF product portfolio for these markets.
For slow heating Fig. The company allows additional tests when necessary and the commercial iryanox is helpful an fast.
In our case we were interested in the polymorphism of polymer additives, which is a much less studied field, 9—11 but which might have an impact on.