LECROY 9410 MANUAL PDF

I REMOTE CONTROL MANUAL g g. II. II. II. | g. II g. II g. I li g a. Serial Number. May MODELS /14/20/24/30/ DUAL- AND QUAD-CHANNEL. 5 Manual Operation. Vertical Controls. Time-Base Controls. Probes. Bandwidth Limit. Trigger controls (Standard). Displaying Traces. Display Control and. See Remote Control Manual. 6FRSH ([SORUHU. Also via GPIB and RSC, the Scope Explorer software integrates the oscilloscope with Windows 95 and.

Author: Gorn Samura
Country: Chad
Language: English (Spanish)
Genre: Spiritual
Published (Last): 25 September 2013
Pages: 378
PDF File Size: 14.60 Mb
ePub File Size: 1.29 Mb
ISBN: 572-1-18481-671-2
Downloads: 2254
Price: Free* [*Free Regsitration Required]
Uploader: Tygotaur

Then the 13 screws can be removed which frees the board.

Teledyne LeCroy – Product Manuals – Oscilloscopes

In order to get access for adjustment, put the scope on its rear feet and pivot the pover supply unit slightly manial from the display board. Leroy entire cycle is minimum nsec 8 BCK clock periods. It won’t trigger, but I think that’s a side effect more than the fault itself.

While Vin and Vout are different, the capacitor is charged or discharged with a rate given by Iin, the integrator current, until Vout reaches Vin.

The rear panel assembly can be removed from the DSO. It provides high resolution and wide-band spectrum analysis together with sophisticated win- dow functions and fast processing. Versatile display formats – Frequency-domain data may be presented as magnitude, phase, real, imaginary, com- plex. Box Meyrin 1-Geneva, Switzerland Telephone: The tube 6 with the deflection yoke 8 can now, with care, be removed without lecroh other boards having to be moved.

  ABSITE FISER PDF

Plug the mains cable back into the outlet and wait for the scope to turn on. These arithmetic functions can be performed on any source waveform on a point by point basis.

Full text of “LeCroy Service Manual”

Additive constant on input: The display processor is set in a wait state. The hardware disconnects automaticaly the 50 Ohm resistor! Autostore – Waveforms can be automati- cally stored to the card after every acquisition. And so far the PSU doesn’t mind.

In contrast, digital oscillo- scopes offer much better measurement precision, easy transient capture and the possibility of automation. A voltage to current converter follows the sample-and -hold and provides the appropriate range.

The Nyquist frequency can be adjusted and optimized after signal acquisition and prior to FFT execution. You could check the internal clocks signal. This circuit is able to trigger on different TV line number standards see table 5. Is there any chance you might be able to procure the specs?

Repetitive signals with ampli- tudes between 2 mV and 8 V, frequency above 50 Hz and a duty cycle greater than 0. The adjustment of the trigger level is described in the test and calibration procedure of the F front end. The positive mankal is fed with the signal and the negative input with the offset control source. A special hardware feature of the F diaplay is the “pointed” vectors with an intensified point at the end, used to highlight the manhal digitized data points out of the linear interpolation.

  INVESTING 101 KATHY KRISTOF PDF

LeCroy 9410 Manuals

I would start with the timebase board. The DCK signal is a delayed clock used by the time base for exact timing. Digital to Analog Correspondence For all move vectors, the X and Y rates are maximum and equal to hex.

On a flat screen, the spot position is proportional to the tangent of the current. If one neglects the losses in the yoke and pecroy yoke driver, the maximum attainable velocity is: The line G controls the data driver output state. There are five cables connected to the F Each channel has 4 analog controls.

Now the front panel assembly can be removed from the DSO. Offset range problem error code Cheers, Gil Wow that was very kind of you!

LeCroy GmbH, Greece: Waveform data can be stored at rates un- matched in the industry onto or Kbyte cards.