View and Download LUX TX Series installation and operating instructions online. TX Series Thermostat pdf manual download. Thermostats such as the Lux , the Smart Temp , TX, Lux HP are functional energy saving tools, but when Follow these instructions to reprogram it to the schedule you want. My Lux TX E is locked – how do I unlock it?. Buy Lux TXE for the lowest price available online! Presenting the new Lux ® TXE, a programmable thermostat that allows users to easily Manuals (3).
|Published (Last):||25 October 2005|
|PDF File Size:||13.30 Mb|
|ePub File Size:||10.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
LUX TX500 Series Installation And Operating Instructions
Janual warranty gives you specific legal rights and you may also have other rights which vary from state to state. What do I do to reset temperature, time and other settings? This setting tells the thermostat about the type of heating and cooling equipment that it is controlling, so that the system is operated properly.
All of the settings, options, and components listed in this section are located on the rear tx5000e the thermostat, on the circuit board. If painting or construction work has yet to be completed, cover the unit completely or do not install it. Hold the base against the wall. You should see the word SET appear on the display, along with the clock and a day of the week that is flashing.
Lux Txe Wiring – Wiring Diagram Todays
On new installations, follow the guidelines listed below. To enter a Hold, push the HOLD button once, and the word Hold will appear in the temperature portion of the screen, along with the set temperature flashing. This lx is protected against normal mxnual static electric discharges, however to minimize the risk of damaging the unit in extremely dry weather, touch a grounded metal object before touching your thermostat. Use this setting if you have a Gas or Oil heating system.
Enter text from picture: In the spring and fall or when the windows are open, you can set the switch OFF. Remove the used batteries from the battery mannual and discard appropriately.
In the display window it says “low battery. Don’t show me this message again. Be careful not to drop the body or disturb electronic parts. This can be done at the fuse. Wires must be trapped between the black clamps and the brass terminals as shown here.
Lux Products TX500E Thermostat User Manual
If you are mounting the base to soft material like plasterboard or if you are using the old mounting holes, the screws may not hold. This will damage the thermostat and void your warranty. Click here to share your story. This is manuwl even in the event of a power failure, or if a reset button is pressed.
Other models are slightly different, but follow the same principals. Generalmente, los terminales B y O se usan solamente para sistemas de bombas de calor.
Route the wires oux the hole below the terminal block. Do not install the unit until all construction work and painting has been completed.
This article has also been viewedtimes. Do not locate in a damp area.
Remove the cover carefully, more than likely it snaps on at the bottom and hangs and pivots from two little fingers at the top, pull out on the snaps at the bottom and it should lift off at the top. A larger swing number decreases the number of cycles ts500e hour, but saves energy in most cases.
Do not install it where there are unusual heating conditions, such as: Attach the base to the wall with the two screws provided. Smart temp universal 7-day programmable touchscreen thermostat 35 pages. Open the thermostat tx500d press “reset” with an open paperclip or other small pointy object.
Not Helpful 3 Helpful 1. Press up on the button on bottom of thermostat and swing the body away from the base. These same programming steps for all four periods must be performed in both Heat and Cool Temperature modes independently. The time amount for this delay is fixed at 5 minutes between on or off load changes. Turn the dial to Run and close the cover.
On replacement installations, mount the. This reset clears all of the heating and cooling programs, filter settings, and other user ulx preferences to their default values.
This will save you time and minimize the chance of dam. Is there a battery?
Lux Products Thermostat TXE User Guide |
Return the dial to the RUN position once you are finished viewing the filter life remaining. Complete, Easy To Read. Generally, the B and O terminals are only used for Heat Pump systems.
When you are finished, press NEXT. It’s a community-based project which helps to repair anything.
When they are all labeled, carefully remove the wires one at a time, making sure that they do not fall back inside the wall.